New Outboard BlockMercury · Yamaha · Johnson · Evinrude · OMC 251.645.2050

New & remanufactured · built in the USA since 1982

“Block” means four different things.

Ask three shops for a block and you will get three different quotes, because the word covers everything from a bare casting to a complete assembly. The gap between them is thousands of dollars and a weekend of labor. Here is what each one actually includes, what you carry over from the old motor, and which ones exist for your engine.

What each one includes

Read across. A filled square comes assembled on the part you buy. A dashed square is something you move over from your own motor, which also means it has to be in good enough shape to reuse.

Comes on the part You transfer your own
You are buying Block & bores Crank & rods Pistons & rings Head & valvetrain Induction & ignition
Bare blockThe casting and the cylinders, nothing turning inside it. yours yours yours yours
Short blockBottom end assembled and measured, ready for your top end. yours yours
Cylinder headTop end only, when the bottom end came through clean. yours yours yours yours
Complete powerheadThe whole assembly, ready to set down on the midsection. yours

Every one of them stops short of your carburetors, injectors, switch boxes and ignition modules. Those come off the old motor and go back on, which is exactly why OBR's break-in procedure tells you to rebuild the carburetors, flow test the injectors and check the switch boxes before anything turns over.

In the catalog Complete powerheads across Mercury and Mariner, Yamaha, and OMC Johnson and Evinrude, plus four-stroke short blocks. Mostly remanufactured, with new units where they are offered.
Browse powerheads & short blocks →
Quote by phone Bare blocks and cylinder heads are not listed online. They are real items, they just get priced against your model and serial number.
Send the model number →

Two-stroke or four decides the menu

It is not a preference, it is how the engines are built. Which unit you buy depends on where your motor keeps its valves.

Two-stroke

Sold as a complete powerhead

There is no separate valvetrain worth saving, so the head is a cover over the combustion chamber rather than half the engine. Splitting a two-stroke into a short block buys you nothing, which is why you will not find a two-stroke short block anywhere, including here.

Carbureted, EFI and direct injected are all still two-strokes for this purpose, FICHT and E-TEC included.

Two-stroke powerheads →
Four-stroke

Short block is usually the smart buy

The head carries the camshafts, valves and often the variable valve timing hardware, and it is frequently undamaged by whatever killed the bottom end. Every short block OBR lists is a four-stroke.

Buy the short block, inspect and clean your own head, and confirm the valve shimming is in spec before it goes back on.

Four-stroke short blocks →

The mistake that is not covered

When a four-stroke lets go, the metal it shed did not stay in the block. The oil pump pushed it through the whole oil system, and it is still sitting in the midsection, the oil pan and the pickup screen after the block comes off. Bolt a clean short block onto that and the same debris goes straight through the new engine and ruins it too.

  • Thoroughly clean the midsection and oil pan. OBR recommends taking the oil pan fully apart to do it.
  • Remove and replace the oil pickup screen.
  • On VVT engines, inspect and clean the pulleys and solenoids as well.
  • Change the oil and filter after the first 30 minutes on a test tank, then again at 10 hours.
  • Inspect and replace as necessary: timing belts, tensioners and pulleys. Set the timing per the manufacturer's procedure.

Failures caused by oil system contamination are not covered under warranty.

Read the full break-in procedure →

Technician assembling an outboard powerhead at the OBR bench in Semmes, Alabama

Two oil pumps worth writing down

OBR's remanufactured Yamaha short blocks require a specific oil pump. Order it with the block rather than finding out mid-install.

Yamaha F200 / F225 / F250 3.3L short blocks
6P2-13300-00-00  ·  OBR YA-282
Yamaha 2.7L F150 short blocks
63P-13300-02-00  ·  OBR YA-281

Narrow it down

Every link opens the OBR catalog already filtered, with current availability showing against each part number.

See every block and powerhead in the catalog →

Not sure which one you need?

Read us the model and serial number off the engine, and tell us what it sounded like when it let go. That usually settles short block versus powerhead in one call. Shops and dealers order wholesale.